OPL9815

OPL9815.png
OPL9815

About

The OPL9815 is a Bluetooth™ laser scanner from Opticon, features GPS, a real-time clock and 18-key operation for data-capture applications that require location and time stamps, as well as data entry. The OPL9815 is perfect for inventory, logistics, warehouse and retail applications. Since the OPL9815 is programmable, channel partners can create custom solutions around the OPL9815 using the free SDK from Opticon.

The OPL9815 can transmit data via Bluetooth™ connection, or store data onboard for later transfer via IrDA through a charging cradle (sold separately). The charging cradle is available with a serial, modem or GSM interface. OPL9815 product highlights include:

Setup with NetO32

Follow these directions for first time setup, software installation, and configuration for transferring data from the OPL9815.

Setting up the Host

Collect Materials

You will need the following items.

Assembly

  1. Connect the 32-00606-00 power adapter to a power outlet.
  2. Connect the 32-00606-00 power adapter to the CRD9723.
  3. Connect the communication cable to the CRD9723.
  4. Connect the communication cable to the computer.

Software Installation

In this section we step through installing both Opticon's USB drivers and NetO32.

Installing USB Drivers

If you are using RS232 please skip to Installing NetO32. Opticon's USB drivers need to be installed for the cradle to be properly via USB.

  1. Download the USB drivers from the Driver Downloads section.
  2. Open the zip file by double clicking on it.
  3. Launch the installer by double clicking on it.
  4. Follow the prompts to finish the installation.

Installing NetO32

The OPL9815 uses a piece of windows software called NetO32 to save the data file to the computer. To install NetO32 follow the steps below.

  1. Download NetO32 from the Software Downloads section.
  2. Open the zip file by double clicking on it.
  3. Launch the installer by double clicking on it.
  4. Follow the prompts to finish the installation.

Configuring NetO32

NetO32 is now in 'Polling' mode. Note that you should see the yellow light on the cradle blinking steadily. This means it will sit here indefinitely sending queries to the cradle and waiting for the right response to start a download. Multiple downloads can all be done without ever closing NetO32. When you are done using NetO32 simply select 'Protocol' > 'Stop' and NetO32 will discontinue polling mode. The application can then be closed.

Starting the Upload from your OPL9815

After NetO32 is in Polling mode (see above) follow these steps. Note that you should see the yellow light on the cradle blinking steadily. This means it will sit here indefinitely sending queries to the cradle and waiting for the right response to start a download. Multiple downloads can all be done without ever closing NetO32. When you are done using NetO32 simply select 'Protocol' > 'Stop' and NetO32 will discontinue polling mode. The application can then be closed.

Bluetooth Setup

Navigate to the System Menu > Communicate > Interface and select BT Real Time Use the CLR button to back out of the Interface, Communicate, and System Menus Be sure to choose YES when asked to save settings while exiting the System Menu.

Navigate to Scan labels and press UP for SLAVE. The screen will display "Waiting Host Connection"... On your Computer/Tablet/Phone, search for the Bluetooth device OPL-9815_xxxx The scanner will ask you to confirm the PIN. Be sure to use the ENT key.

The device will be paired in HID mode. In SPP mode you will need to open the serial port to complete the pairing process.

You can change between Bluetooth-HID (Keyboard) mode and Bluetooth-SPP (Serial) mode by navigating to System Menu > Bluetooth > Set Mode Press UP for HID or DOWN for VCP(SPP).

Loading Firmware

Follow the directions above for Setting up the Host.

Software Installation

Follow the Directions above for Installing USB Drivers

Installing Appload

  1. Appload is Opticon's multi-purpose utility for installing firmware onto devices such as the OPL9815. To install Appload follow the steps below.
  2. Download Appload from the Downloads Software Section.
  3. Open the zip file by double clicking on it.
  4. Launch the installer by double clicking on it.
  5. Follow the prompts to finish the installation.

Configuring Appload

This section outlines how to configure Appload to communicate with the OPL9815. Appload is a PC application used to load firmware on most of Opticon's products.

Select COM Port

  1. Select Settings
  2. Select Port
  3. Select the appropriate Port number so that it will match the COM port of either the USB or RS232 interface (whichever was used).
    1. If you are using an RS232 interface the physical serial port is usually assigned COM1 by Windows so if you are using an RS232 interface this is likely your COM port number.
    2. If you are using a USB interface then select the COM port will usually be a number between 2 and 250. The cradle should identify itself as an 'Opticon OPL/CRD USB Serial Port'.

Set IrDA type

  1. Select Settings
  2. Select IrDA Adapter/cradle type
  3. Select Not Installed

Download Firmware

You will need to download and unzip the appropriate firmware file for the action you wish to perform from the Software Downloads section.

Loading the Firmware

OPL9815 Firmware Setup

Load the Firmware

Application Development

The OPL9815 firmware is split into two levels, an Operating System and an Application. The Operating System Exposes the functions of the hardware to the Application level firmware, and the Application determines how the device behaves. The Operating System is developed and maintained solely by Opticon, however anyone can make an application for the OPL9815 using using the C-Library Kit. For code samples please write devsupport@opticonusa.com.


Downloads

Notice: The downloading and use of any Opticon software implies consent with Opticon's End User License Agreement.

Documents

Document Description Version Download
Datasheet Technical details at a glance. Download
Specification Manual This document provides detailed specifications for the OPL9815. For advanced users and system integrators only. Download
Universal Menu Book The Universal Menu Book is a document containing instructions and configuration options for the majority of Opticon's products. Support of the commands in this manual is product specific. A must read for System Integrators. In effect this is the User Manual for all of Opticon's products that do not have a User Manual of their own and a supplement to all others. December 2009 Download

Software

Software Description Version Download
Appload Appload Is Opticon's multi-purpose firmware update utility. It is a Windows PC application that provides the capability to download firmware onto most Opticon products. It also contains a versatile terminal interface that allows serial communication to any serial port connected to the PC (be it RS232, USB-VCP or Bluetooth-SPP). Opticon products can be queried and configured in this manner. EAGV0177
1.77
Download
NetO32 A PC application implementing the NetO protocol to transfer files from the PC to the terminal barcode reader. EGF2001H (2.1.0.0) Download
OseComm32 A PC application implementing the OseComm protocol to transfer files from the PC to the terminal bar code reader and a variety of other file-related functions. 1.0.17.0 Download
Firmware: OS This is the latest Operating System firmware file for the OPL9815. XBOV0213 Download
Firmware: Application This is the latest standard application firmware file for the OPL9815. XFOS0879 Download
C-Library Kit The C-Library Kit is Opticon's SDK for developing custom firmware for many of Opticon's product families (OPN, OPL97xx, OPL98xx, OPH, etc.). Included find sample code, full application samples, library files, documentation, compilers for certain products and more. This download is a zipped collection of the installer and associated files. The Toshiba C Compiler requires a separate download which is located here 2.38 Download

Drivers

Driver Description Version Download
All-In-One PC Drivers USB-to-serial drivers installer package for 32 and 64-bit versions of Windows XP (32-bit only), Vista 7, 8, 8.1 and 10. This package contains four drivers. The first and fourth drivers are for the Opticon cradles. The second driver is for the OPN200x scanners along with many other Opticon products. The third driver is an ATEN driver for a popular RS232 <-> USB-VCP adapter. You can choose any of the drivers to install on the first screen of the installer program. *Note: Opticon USB Drivers may not install or operate correctly if FIPS (Federal Information Processing Standards) is enabled on your host computer* 1.615 Download





Categories: OPL  | GPS  | Data Collector  | Bluetooth  | Wireless Solutions