Version Differences for Opticonfigure

Revision as of 23 May 2012 07:14

(→Data Wizard)

Revision as of 25 September 2012 07:51

(→Data Wizard)

 Opticonfigure is an online version of our Universal Menu Book. It can be used to create custom and condensed printouts of your desired settings for quick reference and setup.
 ==Data Wizard==
-								Many of Opticon's scanners support Advanced Data Formatting using a tool called Data Wizard. With Data Wizard, barcodes can be altered by the scanner prior to their being transmitted to a host device. Most Opticon scanners support up to three simultaneous Data Wizard configurations, and some scanners support even more.
+								Many of Opticon's scanners support Advanced Data Formatting using a tool called [[Data Wizard]]. With Data Wizard, barcodes can be altered by the scanner prior to their being transmitted to a host device. Most Opticon scanners support up to three simultaneous Data Wizard configurations, and some scanners support even more.
-								===Using Data Wizard===
-								[http://opticonfigure.opticon.com/ Opticonfigure] can be used to generate Data Wizard barcode sheets. Simply go to Opticonfigure, and choose Data Wizard from the tabs at the top left. Make sure that ''Enable data wizard config'' is selected, then click ''Add''.
-								Next, click ''Advanced'' to proceed.
-								'''Matching Conditions'''
-								Here, multiple matching conditions can be selected. Each additional condition will narrow down the matching even further, and matching conditions don't change the barcode data.
-								*'''Match bar code ID''': If you want to alter all barcodes of a specific symbology like UPC-A or Code-39, choose this option.
-								*'''Match barcode length''': If you want to alter barcodes of a specific length, from 1 character to 99 characters, choose this option.
-								*'''Match barcode characters''': Choose this option to only alter barcodes with up to three matching consecutive characters in them. For example, if you chose BCD, then Data Wizard would match barcodes containing BCD, ABCD, or BCDA, but not BACD or BACAD.
-								**'''Match fixed position''' causes Data Wizard to look for the given character string, starting at the given position. Choosing position 0, for example, only matches barcodes that start with your pattern. Choosing position 1 matches barcodes with a single character followed by your pattern, choosing 2 matches two characters followed by your pattern, and so on.
-								When you are finished deciding what barcodes you want to match, choose Next to continue.
-								'''Build output'''
-								On this next screen you choose how you would like your output to be altered. You can chop characters off the beginning and end of the barcode, start or end at a particular character(keeping it or dropping it), and also simply add an extra character to the start of the code. These options are clustered into two groups so that you can take multiple pieces from the same barcode.
-								'''Add Character''': Add character allows you to add an extra character to the start of a barcode.
-								''Start from...''
-								* '''Start from position''': This allows you to clip off characters from the beginning of a barcode, with position 0 being the first character. So, with the barcode 0123456, choosing start from position 0 would give you 0123456, position 1 would give you 123456, position 2 would give you 23456, and so on.
-								* '''Start from relative position''': This also allows you to remove characters from the beginning of the barcode, only this time position 0 is the last character. With this option, and the same barcode, position 1 would give you 6, position 2 would give you 56, position 3, would give you 456, and so on.
-								*'''Start from character, include/exclude''': These two options both start the output at a given character. So if you choose E, and your original barcode is ABCEDF, then with ''start from/include'' you will get EDF, and with ''start from/exclude'' you will get DF.
-								''End at...''
-								* '''Part length''': This option is a count of how many characters long the output data should be, starting from your ''start from...'' position above. So if you choose 0, you will get no barcode data, 1 will give you the first character after your starting position, 2 will give you two characters after, and so on.
-								* '''Relative end position''': Choose this option if you want to also remove characters from the end of your barcode. Choosing 0 gives you the entire rest of the barcode, 1 gives you all but the last character, 2 gives you all but the last two characters, and so on.
-								* '''End at character, include/exclude''': These two options both end the output at the given character as before.
-								When you are finished, choose ''Add configuration'' to add that selection to the list. You can add multiple start/end conditions, which allows you to remove multiple portions of a matching barcode. This is useful if you want to remove two parts of a barcode while leaving another part between them intact. To add each portion, construct each as above and select ''Add configuration''.
-								Choose next to move on to the next step in building a configuration, post processing.
-								'''Post processing'''
-								{| border=1 style="float: right; text-align: left; width: 400px; height: 100px;"
-								!
-								! Cut
-								! Fill
-								|-
-								| '''Forward'''
-								| Shorten the barcode from the front
-								| Lengthen the barcode from the front by adding the chosen character
-								|-
-								| '''Backward'''
-								| Shorten the barcode from the back
-								| Lengthen the barcode from the back by adding the chosen character
-								<!--|+ This table may be helpful to understand what each of the four options in this section does.-->
-								|}
-								* '''Replace matching characters''': This will replace each instance of the matching character with a character of your choice.
-								* '''Change output length''':
-								** '''Forward Fill - Backward Cut''': If the barcode is longer than the chosen length, cut characters off the end until it matches the proper length. If the barcode is shorter than the chosen length, add the selected character to the end until it matches the proper length.
-								** '''Backward Fill - Forward Cut''': If the barcode is longer than the chosen length, cut characters off the front. If the barcode is shorter than the chosen length, add the selected character to the back until the barcode has the proper length.
-								**'''Forward Fill - Forward Cut''': If the barcode is longer than the chosen length, cut characters off the front. If the barcode is shorter than the chosen length, add the selected character to the front until the barcode has the chosen length.
-								**'''Backward Fill - Backward Cut''': If the barcode is longer than the chosen length, cut characters off the back. If the barcode is shorter than the chosen length add the selected character to the back until the barcode has the chosen length.
-								===Common Configurations===
-								====How to do a character substitution in Opticonfigure====
-								#Navigate to [http://opticonfigure.opticon.com/ Opticonfigure] in your web browser.
-								#If the Barcode sheet is not already blank then select "Clear Barcode List" from the top right hand corner.
-								#Select Data Wizard.
-								#Select Edit Configuration 1 from the drop down in the top left hand corner.
-								#Select "Enable data wizard config 1", then click Add.
-								#Select "--Start Wizard--"
-								#Select "Only barcodes with certain characters in the code", then click next.
-								#Select "Original output", then click next.
-								#Select "Transmit the original output".
-								#Select "Replace characters, Trim or Fill output to fixed length"
-								#Select "Find characters and replace all of them with specified character"
-								#Select both the character to match and the character to replace it with.
-								# Click next, click finish.