| Line 6: |
| |
|
|
|
| |
===PC=== |
|
===PC=== |
| - |
*1) Download the "OPN-2001 PC Companion Application" under software downloads and the "All In One Installer Package" under driver downloads.
|
+ |
Using the OPN-2003 with a Windows PC requires you to download and install Opticon's PC USB Drivers Installer, and an application to retrieve the data like the PC Companion Application. Both of these are located in the [https://wiki.opticonusa.com/techsupport/en/OPN2003#Downloads Downloads section] of this page.
|
| - |
*2) Double click on the driver installer and follow the instructions.
|
|
|
| - |
*3) Unzip the OPN2001 application file, and copy both items to a convenient location to launch the application from (no installation is required).
|
|
|
| - |
*4) Double click on OPN2001.exe to launch the application.
|
|
|
| - |
*5) Scan barcodes, the connect the OPN2003 to the computer, and click "Get Barcodes"
|
|
|
| - |
*6) Optionally contact Technical support for help with settings.
|
|
|
| |
|
|
|
| |
|
+ |
====Initial Setup====
|
| |
|
+ |
You will only need to do this part once per computer.
|
| |
|
|
|
| |
|
+ |
#Download the "PC USB Drivers Installer" from the [https://wiki.opticonusa.com/techsupport/en/OPN2003#Drivers Driver Downloads section] of this page. Run the installer you downloaded by double-clicking on it. Follow the prompts on your screen until the installation is completed.
|
| |
|
+ |
#Download the OPN-2001 PC Companion Application which is also located in the [https://wiki.opticonusa.com/techsupport/en/OPN2003#Software Software Downloads section] of this page.
|
| |
|
+ |
#Run the installer in the zip file you downloaded.
|
| |
|
+ |
# Plug the OPN-2003 into your computer. Windows will inform you that it has found new hardware, and that it is installing the drivers for that hardware. Then you will see the status indicator in the application window turn green. From the application window you can download barcodes, change settings, or view and set the date and time on the device.
|
| |
|
|
|
| |
|
+ |
====Scan Barcodes====
|
| |
|
+ |
Collecting data with the OPN-2003 is as simple as pointing and scanning. Scanning barcodes with the big button or "trigger" will store barcodes, while scanning with the small button or "function" will remove barcodes. Below are some tips about scanning and removing barcodes from the device.
|
| |
|
|
|
| |
|
+ |
*When the OPN-2003 has a good scan, it will chime, the LED on the device will flash green, and the laser will turn off.
|
| |
|
+ |
*When the OPN-2003 deletes a barcode, it will give a different chime than above, and it will flash an Orange LED when it has a good scan.
|
| |
|
+ |
*Deleting the same barcode again when there are no more scans of it present will cause the OPN-2003 to chime for about a second. The LED will also flash red.
|
| |
|
|
|
| |
|
+ |
====Download From the OPN-2003====
|
| |
|
+ |
If you haven't done so yet, refer to the Initial Setup instructions above to get all the proper software installed and ready. This part of the guide assumes that you have already successfully setup your computer to communicate with the OPN-2003.
|
| |
|
+ |
#Plug the OPN-2003 into your computer.
|
| |
|
+ |
#Open the OPN-2001 PC Companion Application by navigating to Opticon\OPN200x in your Start Menu.
|
| |
|
+ |
#Double-check that the "Status" light is green.
|
| |
|
+ |
#Check the box next to "Save to file" if you would like your barcodes to be saved to your computer each time you select "Get Barcodes." By default, the barcodes will be stored in the Documents folder on your computer. To change this, click on the ellipsis(...) button and choose where you would like your barcodes saved.
|
| |
|
+ |
#Click "Get barcodes" to download the barcodes that you just scanned. Double-check that they got saved to your file before proceeding.
|
| |
|
+ |
#Click "Delete barcodes" to erase the barcodes stored on the OPN-2003.
|
| |
===Mac=== |
|
===Mac=== |
| |
In order to set up the OPN-2003 on the Mac, we will need to install the Mac Companion Application and configure the OPN-2003 to connect to the Mac. |
|
In order to set up the OPN-2003 on the Mac, we will need to install the Mac Companion Application and configure the OPN-2003 to connect to the Mac. |
