Version Differences for OPN-3002i - Opticon Technical Support Portal

However, if data qualifying or data output manipulation is required, please contact our technical support group with your requirements and we may be able to provide a solution.

+

==Firmware Loading==

+

Follow the directions below to load firmware on to the OPN-3002i.

+

===Preparation===

+

# Download the Firmware: OS, and Appload for this process available in the [[#Software|Software Downloads]] section. You may also need Opticon's [[#Drivers|USB Drivers]], so please download those as well.

+

# Extract the OPN-3002i OS zip file, the Appload.zip file, the USB Drivers Installer.zip file, and the OPN2006 Firmware - Application files into a convenient folder.

+

# Install the USB Drivers Installer by double-clicking the USB Drivers Installer.exe, which will start the install wizard. The default settings for the installer are fine in most cases so press Install, then ok until you are finished.

+

# Install [[Appload]] by double-clicking the 'Appload Setup.exe' file, which will start the install wizard. The defaults are fine in most cases, so keep clicking 'Next' until you are finished. Appload will launch at the end of the install process.

+

# Connect the OPN2006 to your PC

+

===Install the Firmware===

+

# Launch Appload if it is not already running.

+

# We first need to choose the correct COM port. From the main Appload window, select 'Settings' > 'Port', then choose the port that says 'Opticon USB Code Reader'.

+

# Now we can start downloading the OS. For the Firmware: OS you downloaded and extracted above, please choose 'File', then 'Download', then navigate to and select the file. You should see a progress indicator and the words 'Initializing IRdA' if this is working.

+

# When complete the OPN-3002i will emit a series of beeps and reboot. When the LED is steady RED (indicating charging) or GREEN (indicating fully charged) the process is complete and you may disconnect your OPN-3002i from the PC.

==Application Programs==

 However, if data qualifying or data output manipulation is required, please contact our technical support group with your requirements and we may be able to provide a solution.
 								==Firmware Loading==
 								Follow the directions below to load firmware on to the OPN-3002i.
 								===Preparation===
 								# Download the Firmware: OS, and Appload for this process available in the [[#Software|Software Downloads]] section. You may also need Opticon's [[#Drivers|USB Drivers]], so please download those as well.
 								# Extract the OPN-3002i OS zip file, the Appload.zip file, the USB Drivers Installer.zip file, and the OPN2006 Firmware - Application files into a convenient folder.
 								# Install the USB Drivers Installer by double-clicking the USB Drivers Installer.exe, which will start the install wizard. The default settings for the installer are fine in most cases so press Install, then ok until you are finished.
 								# Install [[Appload]] by double-clicking the 'Appload Setup.exe' file, which will start the install wizard. The defaults are fine in most cases, so keep clicking 'Next' until you are finished. Appload will launch at the end of the install process.
 								# Connect the OPN2006 to your PC
 								===Install the Firmware===
 								# Launch Appload if it is not already running.
 								# We first need to choose the correct COM port. From the main Appload window, select 'Settings' > 'Port', then choose the port that says 'Opticon USB Code Reader'.
 								# Now we can start downloading the OS. For the Firmware: OS you downloaded and extracted above, please choose 'File', then 'Download', then navigate to and select the file. You should see a progress indicator and the words 'Initializing IRdA' if this is working.
 								# When complete the OPN-3002i will emit a series of beeps and reboot. When the LED is steady RED (indicating charging) or GREEN (indicating fully charged) the process is complete and you may disconnect your OPN-3002i from the PC.
 ==Application Programs==