| Line 14: |
| |
==Related Products== |
|
==Related Products== |
| |
* [[CRD1006]]: Charging and communication cradle for the OPH-1005 with RS232 and USB interface |
|
* [[CRD1006]]: Charging and communication cradle for the OPH-1005 with RS232 and USB interface |
| |
|
|
|
| |
|
+ |
==Firmware Loading==
|
| |
|
|
|
| |
|
+ |
Follow the directions below to load firmware on to the OPN-3002i.
|
| |
|
|
|
| |
|
+ |
===Preparation===
|
| |
|
+ |
# Download the Firmware: OS, and Appload for this process available in the [[#Software|Software Downloads]] section. You may also need Opticon's [[#Drivers|USB Drivers]], so please download those as well.
|
| |
|
+ |
# Extract the CRD-1004 OS zip file, the Appload.zip file, and the USB Drivers Installer.zip file.
|
| |
|
+ |
# Install the USB Drivers Installer by double-clicking the USB Drivers Installer.exe, which will start the install wizard. The default settings for the installer are fine in most cases so press Install, then ok until you are finished.
|
| |
|
+ |
# Install [[Appload]] by double-clicking the 'Appload Setup.exe' file, which will start the install wizard. The defaults are fine in most cases, so keep clicking 'Next' until you are finished. Appload will launch at the end of the install process.
|
| |
|
+ |
# Connect the CRD-1004 to your PC via the USB cable and make sure the power adaptor is plugged in as well.
|
| |
|
|
|
| |
|
+ |
===Install the Firmware===
|
| |
|
+ |
# Launch Appload if it is not already running.
|
| |
|
+ |
# We first need to choose the correct COM port. From the main Appload window, select 'Settings' > 'Port', then choose the port that says 'Opticon OPL/CRD USB Serial Port'.
|
| |
|
+ |
# Now we can start downloading the OS. For the Firmware: OS you downloaded and extracted above, please choose 'File', then 'Download', then navigate to and select the file. You should see a progress indicator and the words 'Initializing IRdA' if this is working.
|
| |
|
+ |
# When complete Appload will prompt you with a download complete message. When you see this message, the process is complete.
|
| |
|
|
|
| |
|
+ |
==Modify Network Settings==
|
| |
|
|
|
| |
|
+ |
To access the network settings:
|
| |
|
+ |
<ol>
|
| |
|
+ |
<li>open up Appload and select the correct COM Port by going to Settings > Port > Opticon OPL/CRD USB Serial Port. </li>
|
| |
|
+ |
<li>Click on Utilities > Show RS232 Data.</li>
|
| |
|
+ |
<li>Settings > Baudrate 115200.</li>
|
| |
|
+ |
<li>Type in terminal window: +++ rapidly. To do this: Press and hold the Shift key down and rapidly press the - key on the keyboard 3 times:
|
| |
|
+ |
This will display the following information below:</li>
|
| |
|
+ |
</ol>
|
| |
|
+ |
<font color = "red">+++</font><font color = "blue"><CR></font><br>
|
| |
|
+ |
<font color="blue">
|
| |
|
+ |
<CR><br>
|
| |
|
+ |
<LF>------------------------------------------------<CR> <br>
|
| |
|
+ |
<LF>Opticon Ethernet Cradle Configuration (NBGV0105)<CR> <br>
|
| |
|
+ |
<LF>------------------------------------------------<CR> <br>
|
| |
|
+ |
<LF><HT>1: Show current settings.<CR> <br>
|
| |
|
+ |
<LF><HT>2: Change board host name.<CR> <br>
|
| |
|
+ |
<LF><HT>3: Change default IP address.<CR> <br>
|
| |
|
+ |
<LF><HT>4: Change default gateway address.<CR> <br>
|
| |
|
+ |
<LF><HT>5: Change default subnet mask.<CR> <br>
|
| |
|
+ |
<LF><HT>6: Change default DNS server address.<CR> <br>
|
| |
|
+ |
<LF><HT>7: Enable DHCP.<CR> <br>
|
| |
|
+ |
<LF><HT>8: Disable DHCP.<CR> <br>
|
| |
|
+ |
<LF><HT>0: Save & Quit.<CR> <br>
|
| |
|
+ |
<LF><CR> <br>
|
| |
|
+ |
<LF>Enter a menu choice (1-0): <br>
|
| |
|
+ |
</font> <CR>
|
| |
|
|
|
| |
|
+ |
This mode will show the current firmware that is loaded onto the cradle and allows you to modify the following settings:
|
| |
|
+ |
<ul>
|
| |
|
+ |
<li>Subnet mask,</li>
|
| |
|
+ |
<li>default gateway address</li>
|
| |
|
+ |
<li>default IP address</li>
|
| |
|
+ |
<li>default DNS server address</li>
|
| |
|
+ |
<li>Enable / Disable the DHCP.</li>
|
| |
|
+ |
</ul>
|
| |
|
|
|
| |
|
+ |
==Change IP address to Static==
|
| |
|
+ |
To set static address enter Network settings mode and press 3
|
| |
|
|
|
| |
|
+ |
Type in something like 10.10.10.10
|
| |
|
|
|
| |
|
+ |
As seen below:
|
| |
|
+ |
<font color="blue">
|
| |
|
+ |
<br>
|
| |
|
+ |
<LF>Enter a menu choice (1-0): </font> <font color ="red"> 3 </font> <font color = "blue">
|
| |
|
+ |
<CR><br>
|
| |
|
+ |
<CR><br>
|
| |
|
+ |
<LF>Default IP Address (172<NUL>.30<NUL>.xxx<NUL>.xx<NUL>): <font color ="red"> 10.10.10.10</font><br>
|
| |
|
+ |
</font>
|
| |
|
|
|
| |
|
+ |
After this the address should be changed. To confirm this press 1 to check the current settings on the device.
|
| |
|
+ |
As displayed below:
|
| |
|
|
|
| |
|
+ |
<font color="blue">
|
| |
|
+ |
<LF>Firmware Version: NBGV0105<CR><br>
|
| |
|
+ |
<LF>Bootloader Version: NAGV0100<CR><br>
|
| |
|
+ |
<LF>Board name: OSE_ETHERNET <NUL><CR><br>
|
| |
|
+ |
<LF>MAC Address: 00-12-6A-00-1C-35<CR><br>
|
| |
|
+ |
<strong><LF>Local IP Address: 10<NUL>.10<NUL>.10<NUL>.10<NUL><CR></strong><br>
|
| |
|
+ |
<LF>Gateway Address: 172<NUL>.30<NUL>.xxx<NUL>.x<NUL><CR><br>
|
| |
|
+ |
<LF>Subnet mask: 255<NUL>.255<NUL>.255<NUL>.0<NUL><CR><br>
|
| |
|
+ |
<LF>Primary DNS server: 1<NUL>.1<NUL>.1<NUL>.1<NUL><CR><br>
|
| |
|
+ |
<LF>Secondary DNS server: 0<NUL>.0<NUL>.0<NUL>.0<NUL><CR><br>
|
| |
|
+ |
<LF>DHCP: Enabled<CR><br>
|
| |
|
+ |
<LF><CR><br>
|
| |
|
+ |
<LF>Press any key to continue...<br>
|
| |
|
+ |
</font>
|
| |
|
|
|
| |
|
+ |
This confirms the current static IP address is set to 10.10.10.10. After setting the IP address make sure to press 0 to save and quit the network settings.
|
| |
|
|
|
| |
|
+ |
==Change Static IP address back to Dynamic==
|
| |
|
+ |
<ol>
|
| |
|
+ |
<li> Enter Network Settings Mode </li>
|
| |
|
+ |
<li> Press 7 to Enable DHCP then press 0 to save and quit the network settings. </li>
|
| |
|
+ |
<li> Re-open the RS232 data screen. Then enter Network Settings Mode again. </li>
|
| |
|
+ |
<li> Plug the ethernet cable (that has a current network connection) into the cradle.</li>
|
| |
|
+ |
<li>Press 1 to confirm the Local IP address has been reset</li>
|
| |
|
+ |
<li> Press 0 to save and quit the network settings </li>
|
| |
|
+ |
</ol>
|
| |
|
|
|
| |
|
+ |
==Downloads==
|
| |
|
|
|
| |
|
+ |
{{EULA_Block}}
|
| |
|
|
|
| |
|
+ |
===Software===
|
| |
|
|
|
| |
|
+ |
{{dt_header|Software}}
|
| |
|
+ |
|-
|
| |
|
+ |
{{dtr_Appload}}
|
| |
|
+ |
|-
|
| |
|
+ |
| Firmware: OS || This is the Operating System firmware for the CRD-1004. The program utility [[Appload]] (see above) is required for loading the OS onto the CRD-1004.
|
| |
|
+ |
| class="center" | NBGV0105
|
| |
|
+ |
| class="center" | [http://ftp.opticonusa.com/Downloads/TC02Jxx.zip Download]
|
| |
|
+ |
|-
|
| |
|
+ |
{{table_end}}
|
| |
|
+ |
===Drivers===
|
| |
|
|
|
| |
|
+ |
{{dt_header|Driver}}
|
| |
|
+ |
|-
|
| |
|
+ |
{{dtr_usb_drivers_allinone_pc}}
|
| |
|
+ |
|-
|
| |
|
+ |
{{table_end}}
|
| |
|
|
|
| |
|
+ |
[[Category:Cradles]]
|
| |
|
+ |
[[Category:Wireless Solutions]]
|
| |
|
+ |
[[Category:Handheld]]
|
| |
|
|
|
| |
|
+ |
* Contact Us:
|
| |
|
+ |
** In US, Canada & Mexico, contact: support@opticonusa.com
|
| |
|
+ |
** In the rest of the world, contact: support@opticon.com
|
