The CRD-1004 is a charging and communication cradle for the OPH-1004 and OPH-1005. The cradle is equipped with two slots in order to charge both the terminal and a spare battery. The external communication is supported by either an Ethernet or USB interface.
An Ethernet cable is default enclosed. A power supply (100-240V/0.5A, 50/60 Hz, 6V/2A) is sold separately
Follow the directions below to load firmware on to the CRD-1004.
To access the network settings:
This will display the following information below:
<LF>Opticon Ethernet Cradle Configuration (NBGV0105)<CR>
<LF><HT>1: Show current settings.<CR>
<LF><HT>2: Change board host name.<CR>
<LF><HT>3: Change default IP address.<CR>
<LF><HT>4: Change default gateway address.<CR>
<LF><HT>5: Change default subnet mask.<CR>
<LF><HT>6: Change default DNS server address.<CR>
<LF><HT>7: Enable DHCP.<CR>
<LF><HT>8: Disable DHCP.<CR>
<LF><HT>0: Save & Quit.<CR>
<LF>Enter a menu choice (1-0):
This mode will show the current firmware that is loaded onto the cradle and allows you to modify the following settings:
To set static address enter Network settings mode and press 3
Type in something like 10.10.10.10
As seen below:
<LF>Enter a menu choice (1-0): 3 <CR>
<LF>Default IP Address (172<NUL>.30<NUL>.xxx<NUL>.xx<NUL>): 10.10.10.10
After this the address should be changed. To confirm this press 1 to check the current settings on the device. As displayed below:
<LF>Firmware Version: NBGV0105<CR>
<LF>Bootloader Version: NAGV0100<CR>
<LF>Board name: OSE_ETHERNET <NUL><CR>
<LF>MAC Address: 00-12-6A-00-1C-35<CR>
<LF>Local IP Address: 10<NUL>.10<NUL>.10<NUL>.10<NUL><CR>
<LF>Gateway Address: 172<NUL>.30<NUL>.xxx<NUL>.x<NUL><CR>
<LF>Subnet mask: 255<NUL>.255<NUL>.255<NUL>.0<NUL><CR>
<LF>Primary DNS server: 1<NUL>.1<NUL>.1<NUL>.1<NUL><CR>
<LF>Secondary DNS server: 0<NUL>.0<NUL>.0<NUL>.0<NUL><CR>
<LF>Press any key to continue...
This confirms the current static IP address is set to 10.10.10.10. After setting the IP address make sure to press 0 to save and quit the network settings.
Notice: The downloading and use of any Opticon software implies consent with Opticon's End User License Agreement.
|Datasheet||Technical details at a glance.||Download|
|Appload||Appload Is Opticon's multi-purpose firmware update utility. It is a Windows PC application that provides the capability to download firmware onto most Opticon products. It also contains a versatile terminal interface that allows serial communication to any serial port connected to the PC (be it RS232, USB-VCP or Bluetooth-SPP). Opticon products can be queried and configured in this manner.||EAGV0177
|Firmware: OS||This is the Bootloader and Operating System firmware for the CRD-1004. The program utility Appload (see above) is required for loading the Bootloader and OS onto the CRD-1004.||NBGV0105||Download|
|All-In-One PC Drivers||USB-to-serial drivers installer package for 32 and 64-bit versions of Windows XP (32-bit only), Vista 7, 8, 8.1 and 10. This package contains four drivers. The first and fourth drivers are for the Opticon cradles. The second driver is for the OPN200x scanners along with many other Opticon products. The third driver is an ATEN driver for a popular RS232 <-> USB-VCP adapter. You can choose any of the drivers to install on the first screen of the installer program. *Note: Opticon USB Drivers may not install or operate correctly if FIPS (Federal Information Processing Standards) is enabled on your host computer*||1.615||Download|