H22

Revision as of 25 July 2012 20:57 by Jleiseth (Comments | Contribs) | (MCU Firmware (required for upgrading from Version 1.02 to Version 1.09 or later))

About the H22

The H22 is Opticon's newest Windows Mobile Terminal. The main features of H22 are:

  • Windows Mobile 6.5.3 operating system
  • HSDPA/HSUPA 7.2Mbps/2.0Mbps cellular connection
  • 3.7" transflective VGA display with touch window
  • Available with qwerty or numeric keyboard

Accessories

  • Single slot USB cradle
  • 4 slot multicradle with Ethernet support
  • Pistol grip
  • Battery BTR0600 - LBP-02 (same as H21)

Technical details

  • Windows Mobile 6.5.3 operating system
  • IP65 rating
  • Marvell PXA320@806MHz processor with 256MB/512MB RAM/Flash
  • UMTS 800/850/1900/2100MHz
  • GSM/GPRS/EDGE 850/900/1800/1900MHz
  • HSDPA/HSUPA 7.2Mbps/2.0Mbps
  • 3.7" transflective VGA display with touch screen
  • Available with qwerty or numerical keyboard
  • aGPS
  • Bluetooth 2.0 + EDR
  • WLAN 802.11bgn with CCXv4
  • 3.2Mpix autofocus camera
  • 1D or 2D barcode scanner
  • 3.5mm audio connector
  • micro AB USB connector
  • Cradle connector
  • IrDA
  • Accelerometer
  • Ambient Light Sensor
  • Proximity Sensor
  • Optional RFID HF
  • SAM slot (Smart Card slot)
  • MicroSD card slot

Key Combinations

  • Checksum:BR1 + BR2 + Vol_UP
  • Factory Reset:BR1 + BR2 + Power Button
  • SD update IPL: Vol_UP + Vol_DN
  • SD update EBOOT: BR1 + Vol_DN
  • SD update OS: BR1 + Vol_UP
  • SD update IPL+EBOOT+OS: BR1 + BR2 + Vol_DN
  • SA-DIAG: BR2 + Vol_DN

Legend:

  • BR1 = Left scan button
  • BR2 = Right Scan Button
  • Vol_UP = + key on the left side of the device
  • Vol_DN = - key on the left side of the device

Firmware Loading Instructions

MCU Firmware (required for upgrading from Version 1.02 to Version 1.09 or later)

  • Download the latest MCU firmware file from the software section of this page.
  • Extract tMcuFU.exe to the root of a micro sd card, and place the Micro SD card into the H22.
  • Press and hold the "volume down" key and the "right scan" key then turn the H21 on (continue holding both keys).
  • If the sw update does not start press the reset button while hodling "left scan" + "right scan" + "volume down"
  • wait for the sw update to finish

SD card method for loading firmware

  • Download the latest firmware file from the software section of this page.
  • Extract the firmware file to the root of a micro sd card, and place the Micro SD card into the H22.
  • Press and hold the "volume down" key and the "right scan" key then turn the H21 on (continue holding both keys).
  • If the sw update does not start press the reset button while hodling "left scan" + "right scan" + "volume down"
  • wait for the sw update to finish and proceed with the setup wizard

PC connection for loading firmware

  • Connect the H22 to a PC running Windows XP or Windows 7.
  • Install Microsoft Active sync/ Windows Mobile Device Center.
  • Download the latest RUU_xxxx.exe firmware loader file from the software section of this page.
  • Run RUU_xxxx.exe on the PC and follow the instructions

Downloads

Documents

Document Description Download
User Manual Operating instructions for all users. Download

Software

Software Description Download
Firmware: MCU (SD Card Install Method) See upgrade instructions for details on installation. Download
Firmware: Windows Mobile (ActiveSync Install Method See upgrade instructions for details on installation. Download
Firmware: Windows Mobile (SD Card Install Method) See upgrade instructions for details on installation. Download
SDK The H-22 SDK is one part, and is designed to allow a user to write software which can take control of certain device features like the built-in sensors and the display backlight. See the included documentation. Download
H-22 Custom ROM tool The H-22 Custom ROM tool is available for developers. Download


Notice
The downloading and use of any Opticon software implies consent with Opticon's End User License Agreement.