H22
About the H22
The H22 is Opticon's newest Windows Mobile Terminal. The main features of H22 are:
- Windows Mobile 6.5.3 operating system
- HSDPA/HSUPA 7.2Mbps/2.0Mbps cellular connection
- 3.7" transflective VGA display with touch window
- Available with qwerty or numeric keyboard
Accessories
- Single slot USB cradle
- 4 slot multicradle with Ethernet support
- Pistol grip
- Battery BTR0600 - LBP-02 (same as H21)
Technical details
- Windows Mobile 6.5.3 operating system
- IP65 rating
- Marvell PXA320@806MHz processor with 256MB/512MB RAM/Flash
- UMTS 800/850/1900/2100MHz
- GSM/GPRS/EDGE 850/900/1800/1900MHz
- HSDPA/HSUPA 7.2Mbps/2.0Mbps
- 3.7" transflective VGA display with touch screen
- Available with qwerty or numerical keyboard
- aGPS
- Bluetooth 2.0 + EDR
- WLAN 802.11bgn with CCXv4
- 3.2Mpix autofocus camera
- 1D or 2D barcode scanner
- 3.5mm audio connector
- micro AB USB connector
- Cradle connector
- IrDA
- Accelerometer
- Ambient Light Sensor
- Proximity Sensor
- Optional RFID HF
- SAM slot (Smart Card slot)
- MicroSD card slot
Key Combinations
- Checksum:BR1 + BR2 + Vol_UP
- Factory Reset:BR1 + BR2 + Power Button
- SD update IPL: Vol_UP + Vol_DN
- SD update EBOOT: BR1 + Vol_DN
- SD update OS: BR1 + Vol_UP
- SD update IPL+EBOOT+OS: BR1 + BR2 + Vol_DN
- SA-DIAG: BR2 + Vol_DN
Legend:
- BR1 = Left scan button
- BR2 = Right Scan Button
- Vol_UP = + key on the left side of the device
- Vol_DN = - key on the left side of the device
Firmware Loading Instructions
MCU Firmware (required for upgrading from Version 1.02 to Version 1.09 or later)
- Download the latest MCU firmware file from the software section of this page.
- Extract tMcuFU.exe to the root of a micro sd card, and place the Micro SD card into the H22.
- Press and hold the "volume down" key and the "right scan" key then turn the H21 on (continue holding both keys).
- If the sw update does not start press the reset button while hodling "left scan" + "right scan" + "volume down"
- wait for the sw update to finish and proceed with the setup wizard
SD card method for loading firmware
- Download the latest firmware file from the software section of this page.
- Extract the firmware file to the root of a micro sd card, and place the Micro SD card into the H22.
- Press and hold the "volume down" key and the "right scan" key then turn the H21 on (continue holding both keys).
- If the sw update does not start press the reset button while hodling "left scan" + "right scan" + "volume down"
- wait for the sw update to finish and proceed with the setup wizard
PC connection for loading firmware
- Connect the H22 to a PC running Windows XP or Windows 7.
- Install Microsoft Active sync/ Windows Mobile Device Center.
- Download the latest RUU_xxxx.exe firmware loader file from the software section of this page.
- Run RUU_xxxx.exe on the PC and follow the instructions
Downloads
Documents
| Document | Description | Download |
|---|---|---|
| User Manual | Operating instructions for all users. | Download |
Software
| Software | Description | Download |
|---|---|---|
| Firmware: MCU (SD Card Install Method) | See upgrade instructions for details on installation. | Download |
| Firmware: Windows Mobile (ActiveSync Install Method | See upgrade instructions for details on installation. | Download |
| Firmware: Windows Mobile (SD Card Install Method) | See upgrade instructions for details on installation. | Download |
| SDK | The H-22 SDK is one part, and is designed to allow a user to write software which can take control of certain device features like the built-in sensors and the display backlight. See the included documentation. | Download |
| H-22 Custom ROM tool | The H-22 Custom ROM tool is available for developers. | Download |
http://ftp.opticonusa.com/Downloads/H22CustomROMTool.zip
| Notice |
| The downloading and use of any Opticon software implies consent with Opticon's End User License Agreement. |