H22

Revision as of 13 July 2012 14:02 by Jleiseth (Comments | Contribs)

Summary

The H22 is Opticon's newest Windows Mobile Terminal. The main features of H22 are:

  • Windows Mobile 6.5.3 operating system
  • HSDPA/HSUPA 7.2Mbps/2.0Mbps cellular connection
  • 3.7" transflective VGA display with touch window
  • Available with qwerty or numeric keyboard

Technical details

  • Windows Mobile 6.5.3 operating system
  • IP65 rating
  • Marvell PXA320@806MHz processor with 256MB/512MB RAM/Flash
  • UMTS 800/850/1900/2100MHz
  • GSM/GPRS/EDGE 850/900/1800/1900MHz
  • HSDPA/HSUPA 7.2Mbps/2.0Mbps
  • 3.7" transflective VGA display with touch screen
  • Available with qwerty or numerical keyboard
  • aGPS
  • Bluetooth 2.0 + EDR
  • WLAN 802.11bgn with CCXv4
  • 3.2Mpix autofocus camera
  • 1D or 2D barcode scanner
  • 3.5mm audio connector
  • micro AB USB connector
  • Cradle connector
  • IrDA
  • Accelerometer
  • Ambient Light Sensor
  • Proximity Sensor
  • Optional RFID HF
  • SAM slot (Smart Card slot)
  • MicroSD card slot

Accessories

  • Single slot USB cradle
  • 4 slot multicradle with Ethernet support
  • Pistol grip
  • Battery BTR0600 - LBP-02 (same as H21)

Key Combinations

  • Checksum:BR1 + BR2 + Vol_UP
  • Factory Reset:BR1 + BR2 + Power Button
  • SD update IPL: Vol_UP + Vol_DN
  • SD update EBOOT: BR1 + Vol_DN
  • SD update OS: BR1 + Vol_UP
  • SD update IPL+EBOOT+OS: BR1 + BR2 + Vol_DN
  • SA-DIAG: BR2 + Vol_DN

Legend:

  • BR1 = Left scan button
  • BR2 = Right Scan Button
  • Vol_UP = + key on the left side of the device
  • Vol_DN = - key on the left side of the device

Load Firmware

SD card method for loading firmware

  • Download the latest firmware file from the software section of this page.
  • Extract the firmware file to the root of a micro sd card, and place the Micro SD card into the H22.
  • Press and hold the "volume down" key and the "right scan" key then turn the H21 on (continue holding both keys).
  • If the sw update does not start press the reset button while hodling "left scan" + "right scan" + "volume down"
  • wait for the sw update to finish and proceed with the setup wizard

PC connection for loading firmware

  • Connect the H22 to a PC running Windows XP or Windows 7.
  • Install Microsoft Active sync/ Windows Mobile Device Center.
  • Download the latest RUU_xxxx.exe firmware loader file from the software section of this page.
  • Run RUU_xxxx.exe on the PC and follow the instructions

Downloads

Documents

Document Description Download
User Manual Operating instructions for all users. Download

Software

Software Description Download
SDK The H-22 SDK is one part, and is designed to allow a user to write software which can take control of certain device features like the built-in sensors and the display backlight. See the included documentation. Download
Firmware: Windows Mobile (ActiveSync Install Method See upgrade instructions for details on installation. Download
Firmware: Windows Mobile (SD Card Install Method) See upgrade instructions for details on installation. Download


Notice
The downloading and use of any Opticon software implies consent with Opticon's End User License Agreement.