H22

About the H22

The H22 is Opticon's newest Windows Mobile Terminal. The main features of H22 are:

• Windows Mobile 6.5.3 operating system
• HSDPA/HSUPA 7.2Mbps/2.0Mbps cellular connection
• 3.7" transflective VGA display with touch window
• Available with qwerty or numeric keyboard

Accessories

• Single slot USB cradle
• 4 slot multicradle with Ethernet support
• Pistol grip
• Battery BTR0600 - LBP-02 (same as H21)

Technical details

• Windows Mobile 6.5.3 operating system
• IP65 rating
• Marvell PXA320@806MHz processor with 256MB/512MB RAM/Flash
• UMTS 800/850/1900/2100MHz
• GSM/GPRS/EDGE 850/900/1800/1900MHz
• HSDPA/HSUPA 7.2Mbps/2.0Mbps
• 3.7" transflective VGA display with touch screen
• Available with qwerty or numerical keyboard
• aGPS
• Bluetooth 2.0 + EDR
• WLAN 802.11bgn with CCXv4
• 3.2Mpix autofocus camera
• 1D or 2D barcode scanner
• 3.5mm audio connector
• micro AB USB connector
• Cradle connector
• IrDA
• Accelerometer
• Ambient Light Sensor
• Proximity Sensor
• Optional RFID HF
• SAM slot (Smart Card slot)
• MicroSD card slot

How To:

Configure a Static IP Address

On Wifi

First, open Wireless Manager by tapping the wireless connections icon, or by navigating to Start->Settings->Connections->Wireless Manager. From here, select Menu->Wifi-Settings. Choose the Network Adapters tab, and then tap on Broadcom 802.11 DHD Network Adapter.

From this screen you can configure your static IP address, as well as your subnet mask, and default gateway. The Name Servers tab also allows you to configure up to two DNS or WINS servers to query during hostname lookups.

Key Combinations

• Checksum:BR1 + BR2 + Vol_UP
• Factory Reset:BR1 + BR2 + Power Button
• SD update IPL: Vol_UP + Vol_DN
• SD update EBOOT: BR1 + Vol_DN
• SD update OS: BR1 + Vol_UP
• SD update IPL+EBOOT+OS: BR1 + BR2 + Vol_DN
• SA-DIAG: BR2 + Vol_DN

Legend:

• BR1 = Left scan button
• BR2 = Right Scan Button
• Vol_UP = + key on the left side of the device
• Vol_DN = - key on the left side of the device

Auto Install Programs on Cold Boot

Firmware Loading Instructions

MCU Firmware (required for upgrading from Version 1.02 to Version 1.09 or later)

• Download the latest MCU firmware file from the software section of this page.
• Extract tMcuFU.exe to the root of a micro sd card, and place the Micro SD card into the H22.
• Press and hold the "volume down" key and the "right scan" key then turn the H21 on (continue holding both keys).
• If the sw update does not start press the reset button while hodling "left scan" + "right scan" + "volume down"
• wait for the sw update to finish

SD card method for loading firmware

• Download the latest firmware file from the software section of this page.
• Extract the firmware file to the root of a micro sd card, and place the Micro SD card into the H22.
• Press and hold the "volume down" key and the "right scan" key then turn the H21 on (continue holding both keys).
• If the sw update does not start press the reset button while hodling "left scan" + "right scan" + "volume down"
• wait for the sw update to finish

PC connection for loading firmware

• Connect the H22 to a PC running Windows XP or Windows 7.
• Install Microsoft Active sync/ Windows Mobile Device Center.
• Download the latest RUU_xxxx.exe firmware loader file from the software section of this page.
• Run RUU_xxxx.exe on the PC and follow the instructions

Downloads

Documents

Software