| Line 55: |
| |
After NetO32 is in Polling mode (see [[#Configuring_NetO32|above]]) follow these steps. Note that you should see the yellow light on the cradle blinking steadily. This means it will sit here indefinitely sending queries to the cradle and waiting for the right response to start a download. Multiple downloads can all be done without ever closing NetO32. When you are done using NetO32 simply select 'Protocol' > 'Stop' and NetO32 will discontinue polling mode. The application can then be closed. |
|
After NetO32 is in Polling mode (see [[#Configuring_NetO32|above]]) follow these steps. Note that you should see the yellow light on the cradle blinking steadily. This means it will sit here indefinitely sending queries to the cradle and waiting for the right response to start a download. Multiple downloads can all be done without ever closing NetO32. When you are done using NetO32 simply select 'Protocol' > 'Stop' and NetO32 will discontinue polling mode. The application can then be closed. |
| |
* For the purposes of the inital test, please scan some barcodes if you have not yet done so. |
|
* For the purposes of the inital test, please scan some barcodes if you have not yet done so. |
| - |
{{#ifeq: {{{transcludesection}}}|manSend|
|
+ |
{{#ifeq: {{{screen}}}|true|
|
| |
* Select 'Send Data' from the main menu (use the arrow keys to move up and down and trigger (center key) to select an option. |
|
* Select 'Send Data' from the main menu (use the arrow keys to move up and down and trigger (center key) to select an option. |
| |
* The screen that appears should say 'Transmit Data via Cradle NETO Protocol -PRESS ANY KEY-'. Press any key. |
|
* The screen that appears should say 'Transmit Data via Cradle NETO Protocol -PRESS ANY KEY-'. Press any key. |
| |
* The unit will change to say 'Sending File Waiting NetO Connection ...'. At this point simply place the unit on the cradle. |
|
* The unit will change to say 'Sending File Waiting NetO Connection ...'. At this point simply place the unit on the cradle. |
| |
* The {{{prodName}}} will emit a series of short beeps and display 'File Was Sent. Delete Data File?'. Choose either YES or NO by pressing the appropriate arrow button below the display. |
|
* The {{{prodName}}} will emit a series of short beeps and display 'File Was Sent. Delete Data File?'. Choose either YES or NO by pressing the appropriate arrow button below the display. |
| - |
| }}
|
+ |
|
|
| - |
{{#ifeq: {{{transcludesection}}}|autoSend|
|
|
|
| |
* Place the {{{prodName}}} nose down in the cradle. |
|
* Place the {{{prodName}}} nose down in the cradle. |
| - |
| }}
|
+ |
}}
|
| |
* The NetO32 status log will indicate that the data was downloaded. |
|
* The NetO32 status log will indicate that the data was downloaded. |
| |
* Your Data File is now on the PC in the folder specified previously. |
|
* Your Data File is now on the PC in the folder specified previously. |
| Line 96: |
| |
===={{{prodName}}} Firmware Setup==== |
|
===={{{prodName}}} Firmware Setup==== |
| |
* The {{{prodName}}} must be placed into a download mode for firmware to install correctly. To do this follow the steps below. |
|
* The {{{prodName}}} must be placed into a download mode for firmware to install correctly. To do this follow the steps below. |
| |
|
+ |
{{#ifeq: {{{screen}}}|true|
|
| |
|
+ |
* Enter the OS-level system menu on the device (press Up, Trigger, and Down buttons simultaneously)
|
| |
|
+ |
* Choose the menu option to download an application
|
| |
|
+ |
|
|
| |
* Print [http://ftp.opticonusa.com/UniversalMenuBook/Factory.png this] barcode sheet. |
|
* Print [http://ftp.opticonusa.com/UniversalMenuBook/Factory.png this] barcode sheet. |
| |
* Scan the +-DOWNLOAD-+ at the bottom of the sheet. The unit should beep and show a flashing red LED. |
|
* Scan the +-DOWNLOAD-+ at the bottom of the sheet. The unit should beep and show a flashing red LED. |
| |
|
+ |
}}
|
| |
* Return the device to the cradle |
|
* Return the device to the cradle |
| |
|
|
|
