Version Differences for PHL2700 - Opticon Technical Support Portal

Add content

==OS loading==

-

*Cradle baud rate must be set to 115200 (Dip switches:1 ON, 2 OFF, 3 OFF, 4 OFF, 5 ON, 6 ON)

+

The OS can be loaded either through the IRU-2700 cradle, or through the direct load cable for the PHL-2700. The process differs depending on which method you choose to use. All of the downloads referenced in these instructions are available in the Downloads section, below.

-

*With device powered off press [S] + [ENT] + [SCAN] + [PW] - this is a special mode

-

*:Note: Device display will be blank excepting icons along bottom will be darkened

-

*Appload IrDA Adapter/Cradle type must be set to 'Tekram compatible'

-

*Drag and drop OS file (i.e. CBWV0155.HEX)

+

===Through the Direct Load Cable===

+

*Before you begin, make sure that the batteries in the unit are charged to ensure that the unit does not power off during application loading.

+

*Download and install [[Appload]] onto a PC running Windows, and download the OS for the PHL-2700. These will both need to be available in order to load the OS.

+

*With the device powered off, hold [S] and [ENT], and then press [PW] to enter OS Download Mode.

+

*Start [[Appload]] on your PC, and in the Settings menu, change the IrDA Adapter/Cradle type to "No Cradle," and choose the correct COM port for the PHL-2700.

+

*Extract the file in the OS download from above, and drag and drop that file onto the Appload window to start the download. If everything is working, the PHL and Appload will show a percentage to indicate the progress of the download.

+

===Through the IRU-2700 Cradle===

+

*Before beginning, the cradle's baud rate must be set to 115200 (Dip switches:1 ON, 2 OFF, 3 OFF, 4 OFF, 5 ON, 6 ON). The dip switches are located under a small plastic cover on the bottom of the cradle, and can be switched on or off using a fingernail, a paperclip, or a ballpoint pen.

+

*Download and install [[Appload]] onto a PC running Windows, and download the OS for the PHL-2700. These will both need to be available in order to load the OS.

+

*With the device powered off, hold [S], [ENT] and [SCAN], and then press [PW] to enter OS Download Mode.

+

*Start [[Appload]] on your PC, and in the Settings menu, change the IrDA Adapter/Cradle type to "Tekram Compatible," and choose the correct COM port for the PHL-2700.

+

*Extract the file in the OS download from above, and drag and drop that file onto the Appload window to start the download. If everything is working, the PHL and Appload will show a percentage to indicate the progress of the download.

==Application Loading==

The standard demo application can be loaded either through the IRU-2700 cradle, or through the direct load cable for the PHL-2700. The process differs depending on which method you choose to use.

 Add content
 ==OS loading==
-								*Cradle baud rate must be set to 115200 (Dip switches:1 ON, 2 OFF, 3 OFF, 4 OFF, 5 ON, 6 ON)
+								The OS can be loaded either through the IRU-2700 cradle, or through the direct load cable for the PHL-2700. The process differs depending on which method you choose to use. All of the downloads referenced in these instructions are available in the Downloads section, below.
-								*With device powered off press [S] + [ENT] + [SCAN] + [PW] - this is a special mode
-								*:Note: Device display will be blank excepting icons along bottom will be darkened
-								*Appload IrDA Adapter/Cradle type must be set to 'Tekram compatible'
-								*Drag and drop OS file (i.e. CBWV0155.HEX)
 								===Through the Direct Load Cable===
 								*Before you begin, make sure that the batteries in the unit are charged to ensure that the unit does not power off during application loading.
 								*Download and install [[Appload]] onto a PC running Windows, and download the OS for the PHL-2700. These will both need to be available in order to load the OS.
 								*With the device powered off, hold [S] and [ENT], and then press [PW] to enter OS Download Mode.
 								*Start [[Appload]] on your PC, and in the Settings menu, change the IrDA Adapter/Cradle type to "No Cradle," and choose the correct COM port for the PHL-2700.
 								*Extract the file in the OS download from above, and drag and drop that file onto the Appload window to start the download. If everything is working, the PHL and Appload will show a percentage to indicate the progress of the download.
 								===Through the IRU-2700 Cradle===
 								*Before beginning, the cradle's baud rate must be set to 115200 (Dip switches:1 ON, 2 OFF, 3 OFF, 4 OFF, 5 ON, 6 ON). The dip switches are located under a small plastic cover on the bottom of the cradle, and can be switched on or off using a fingernail, a paperclip, or a ballpoint pen.
 								*Download and install [[Appload]] onto a PC running Windows, and download the OS for the PHL-2700. These will both need to be available in order to load the OS.
 								*With the device powered off, hold [S], [ENT] and [SCAN], and then press [PW] to enter OS Download Mode.
 								*Start [[Appload]] on your PC, and in the Settings menu, change the IrDA Adapter/Cradle type to "Tekram Compatible," and choose the correct COM port for the PHL-2700.
 								*Extract the file in the OS download from above, and drag and drop that file onto the Appload window to start the download. If everything is working, the PHL and Appload will show a percentage to indicate the progress of the download.
 ==Application Loading==
 The standard demo application can be loaded either through the IRU-2700 cradle, or through the direct load cable for the PHL-2700. The process differs depending on which method you choose to use.