Version Differences for OPN2004 - Opticon Technical Support Portal

#Click "Get barcodes" to download the barcodes that you just scanned. Double-check that they got saved to your file before proceeding.

#Click "Delete barcodes" to erase the barcodes stored on the OPN-2004.

-

===Mac===

-

In order to set up the OPN-2004 on the Mac, we will need to install the Mac Companion Application and configure the OPN-2004 to connect to the Mac.

-

Note

-

If you are having trouble getting the OPN-2004 to connect to the Mac Companion Application, try printing the PDF that was included with the installer, and scanning the +-USB1-+ barcode on the page. Your OPN-2004 will sound a tone, then after a few seconds it will connect.

-

*1.) To install the Mac Companion Application, download the "OPN-2004 MAC Companion Application" under software downloads near the bottom of this page. Open the resulting folder, and run the installer "Opticon OPN Demo Application.pkg." Follow the prompts until the installation is complete.

-

*2.) Print the PDF document in the same folder titled "Instructions.pdf." This document contains configuration barcodes for the OPN-2004. These barcodes are used to change the behavior of the OPN-2004 when it connects to a computer. Scan the +-USB1-+ driver to set the OPN-2004 up to connect to the Mac Companion Application.

-

*3.) Plug the OPN-2004 into the Mac. At this point the OPN-2004 should be recognized as a network interface.

-

*4.) Start up the OPN-2004 Mac Companion Application using the Finder. It will automatically detect the OPN-2004. The connection can be confirmed by the green "Connected" text in the top right corner of the application.

-

The OPN-2004 and the Mac are now connected and working together.

==Migrating from the OPN2001 or the OPN2003==

If you are migrating from using the OPN2001 or the OPN2003 to the OPN2004 please contact Opticon Tech Support.

 #Click "Get barcodes" to download the barcodes that you just scanned. Double-check that they got saved to your file before proceeding.
 #Click "Delete barcodes" to erase the barcodes stored on the OPN-2004.
-								===Mac===
-								In order to set up the OPN-2004 on the Mac, we will need to install the Mac Companion Application and configure the OPN-2004 to connect to the Mac.
-								Note
-								If you are having trouble getting the OPN-2004 to connect to the Mac Companion Application, try printing the PDF that was included with the installer, and scanning the +-USB1-+ barcode on the page. Your OPN-2004 will sound a tone, then after a few seconds it will connect.
-								*1.) To install the Mac Companion Application, download the "OPN-2004 MAC Companion Application" under software downloads near the bottom of this page. Open the resulting folder, and run the installer "Opticon OPN Demo Application.pkg." Follow the prompts until the installation is complete.
-								*2.) Print the PDF document in the same folder titled "Instructions.pdf." This document contains configuration barcodes for the OPN-2004. These barcodes are used to change the behavior of the OPN-2004 when it connects to a computer. Scan the +-USB1-+ driver to set the OPN-2004 up to connect to the Mac Companion Application.
-								*3.) Plug the OPN-2004 into the Mac. At this point the OPN-2004 should be recognized as a network interface.
-								*4.) Start up the OPN-2004 Mac Companion Application using the Finder. It will automatically detect the OPN-2004. The connection can be confirmed by the green "Connected" text in the top right corner of the application.
-								The OPN-2004 and the Mac are now connected and working together.
 ==Migrating from the OPN2001 or the OPN2003==
 If you are migrating from using the OPN2001 or the OPN2003 to the OPN2004 please contact Opticon Tech Support.