| Line 104: |
| |
** '''Narrow''': Coming Soon! |
|
** '''Narrow''': Coming Soon! |
| |
====Additional Settings==== |
|
====Additional Settings==== |
| - |
The below is a single example of how to perform an advanced configuration. Note that this specific example is a bland of a single ''basic'' change as well as one advanced one. The long string of codes in step seven is obtained by contacting Opticon Technical Support (see link at left).
|
+ |
The Additional Settings tab is a place to configure specific and advanced configuration options.
|
| |
|
+ |
* '''Update''': This button is pressed after you have made your changes and wish them to take effect. Note that it does not matter if the Barcode Reader is enabled or disabled at the time you click the button but that the changes will not take effect unless or until the barcode reader is enabled.
|
| |
|
+ |
* '''Edit''': This button, when clicked, will launch Word Mobile and open the text file that contains additional codes in a free format. See further down in this section for additional details.
|
| |
|
+ |
* '''''Ellipsis Button''''': The button with three dots, called an ellipsis, is used to browse and choose the file that contains all of the additional settings you wish to use. The default file path is: <pre>\My Documents\BCR\InitBCR.bcr</pre>
|
| |
|
+ |
* '''Set defaults''': This button is used to reset ''all'' defaults of the barcode scanner, including options on other tabs.
|
| |
|
+ |
=====Menu Codes=====
|
| |
|
+ |
Menu Codes is the term Opticon uses to indicate a barcode or number/letter combination that has special significance to our barcode scanners. Nearly all of Opticon's products use the same set of menu codes for all possible configuration options. In the case of the H21, many of these options are expressed as buttons and drop down boxes on the various tabs of the Scanner Settings program as described above. A few options, notably those categorized as ''Data Wizard'' options must still be configured manually. These menu codes, when known, are placed in the flat text file Initbcr.bcr as described above. The ''Data Wizard'' is a series of Menu Codes that allow for basic string manipulations such as removing or replacing certain characters within the barcode data or only transmitting certain portions based on matching criteria. Please [mailto:support@opticonusa.com Contact Us] for additional details on these features. A specific example of these codes (used to remove a possible 18th digit from a normally 17 digit VIN) and instruction in their use can be found below.
|
| |
|
|
|
| |
=====How do I strip out the 18th digit from Vehicle Identification Numbers (VINs)===== |
|
=====How do I strip out the 18th digit from Vehicle Identification Numbers (VINs)===== |
| |
* Navigate to '''Start''' > '''Settings''' > '''System''' > '''Scanner Settings''' > '''Code Options''' (tab). |
|
* Navigate to '''Start''' > '''Settings''' > '''System''' > '''Scanner Settings''' > '''Code Options''' (tab). |
| Line 113: |
| |
#Tap 'Additional Settings' (tab) |
|
#Tap 'Additional Settings' (tab) |
| |
#Tap 'Edit' (button) |
|
#Tap 'Edit' (button) |
| - |
#the text "HC" is present by default. Go to a new line and type the following exactly as you see it here: <br />[A00[A0W[A0ZQ1Q8[A12Q0Q00I[A14Q0Q1[A1CQ0Q0[A1L[A18[A1F<br />[A01[A0W[A0ZQ1Q8[A12Q1Q70B[A14Q0Q0[A1CQ0Q1[A1L[A18[A1F
|
+ |
#the text "HC" is present by default. Go to a new line and type the following exactly as you see it here:<pre>[A00[A0W[A0ZQ1Q8[A12Q0Q00I[A14Q0Q1[A1CQ0Q0[A1L[A18[A1F
|
| |
|
+ |
[A01[A0W[A0ZQ1Q8[A12Q1Q70B[A14Q0Q0[A1CQ0Q1[A1L[A18[A1F</pre>
|
| |
#Tap 'ok' to save the text file |
|
#Tap 'ok' to save the text file |
| |
#Tap 'Update' to save these settings |
|
#Tap 'Update' to save these settings |
